Headlight Adaptors 9004/9005/9006/9007 to … Headlight harnesses

1. Connector info

Connectors are clasified by the terminal not the plastic housing:

20140325_184339
A 9005 Male connector

A male connector is the same as the bulb.

 

 

 

 

 

 

 

9005 Female connector
9005 Female connector

A female connector is the same as on the harness and plugs into the bulb.

 

 

 

 

 

Example: If you have a 9006 bulb and are installing a H8 bulb you would want: Male 9006 to Female H8.

 

 

Headlight switch posistion does not make a bulb brighter, The bulb and headlight housing is what changes the bulb light output.

Example: A headlight bulb that is a single filament  (H1, H3, H7, H8, H9) will be the same brightness when the headlight switch is in the low or high position.

Note: If you are installing LED lights please make sure you have the proper operating system, Most LEDS are made to work with a power trigger system.

9004

 

 

 

9004 TO 9005 high beam

9004 to 9005 high beam only
9004 to 9005 high beam only

If you are swaping out your 9004 to a 9005 high beam this harness will plug right in.

9004 socket plugs into your harness, 9005 socket plugs into 9005 bulbs.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harness)

9004 TO 9006 low and 9005 high beam

9004 to 9006 low and 9005 high beams
9004 to 9006 low and 9005 high beams

9004 socket plugs into your harness, 9005 and 9006 sockets plug into 9005 and 9006 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair. (2 harness)

9004 TO 9006 low beam

9004 to 9006 Low beam
9004 to 9006 Low beam

If you are swaping out your 9004 to a 9006 low beam this harness will plug right in.

9004 socket plugs into your harness, 9006 socket plugs into 9006 bulbs.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harness)

9004 to 9007

9004 to 9007This will allow you to install a 9007  bulb in place of your 9004 bulb.

9004 socket plugs into your harness, 9007 socket plugs into 9007 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9004 to H13

9007 to H13
9007 to H13

This will allow you to install a H13  bulb in place of your 9004 bulb.

9004 socket plugs into your harness, H13 socket plugs into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

9004 to H4

9004 to H4
9004 to H4

9004 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

9004 TO H7 low and H7 high

9004 to H7 low and H7 high beam
9004 to H7 low and H7 high beam

This will allow you to install a H7 low beam and H7 high beam bulbs in place of your 9004 bulb.

9004 socket plugs into your harness, H7 and H7 sockets plug into H7 and H7 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair (2 harness)

9004 TO H7 low beam only

9004 to H7
9004 to H7 low beam

This will allow you to install a H7 as a low beam bulbs in place of your 9004 bulb.

9004 socket plugs into your harness, H7 socket plugs ino H7 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9004 TO H8 low and H8 high

This will allow you to install a H8 and H8  bulbs in place of your 9004 bulb.

9004 socket plugs into your harness, H8 and H8 sockets plug into H8 low beam and H8 high beam bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair (2 harness)

9004 to H8 or H11

9007 to H8 Lowbeam only
9004 to H8 Lowbeam only

This will allow you to install a H8/H11 bulb in place of your 9004 bulb.

9004 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired as low beam.

$25.00 pair. (2 harnesses)

9004 TO H9 low and H9 high

9007 to H9low H9high
9004 to H9low H9high

9004 socket plugs into your harness, H9 and H9 sockets plug into H9 and H9 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair (2 harness)

9004 WIG-WAG PIGTAIL

This is a 9004 to 9004 harness so you can add a wig-wag unit without cutting into your factory harness. This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 14 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9005

 

 

 

9005 to 880

9005 to 880 Headlight Adaptor Harness
9005 to 880

This will allow you to install a 880 bulb in place of your 9005 bulb.

9005 socket plugs into your harness, 880 socket plugs into 880 bulb.

made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9005 to 9006

H8/H11 to 9006 Headlight Adaptor Harness
9005 to 9006

This will allow you to install a 9006 bulb in place of your 9005 bulb.

9005 socket plugs into your harness, 9006 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9005 to H1

9005 to Europe H19005 socket plugs into your harness, H1 socket plugs into H1 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This has connector for the bulb and one to ground the bulb.

$25.00 pair (2 harness)

9005 to H4

9005 to H4 low beam only
9005 to H4 high beam only

This will allow you to install a H4 bulb in place of your 9005 bulb. This will only operate the high beam part of the H4 bulb.

9005 socket plugs into your harness, H4 socket plugs into H4 bulb.

This can be used on the Toyota Headlight H4/H1 headlights.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

9005 to H8 or H11

9005 to H8/H11 Headlight Adaptor Harness
9005 to H8/H11

This will allow you to install a H8/H11 bulb in place of your 9005 bulb.

9005 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9005 to H9

9005 to H9
9005 to H9

This will allow you to install a H9 bulb in place of your 9005 bulb.

9005 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9005 Wig-wag pigtail

This is a 9005 to 9005 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

 

 

9006

 

 

 

9006 low and 9005 high beam to 9004

This will allow you to install a 9004 bulb in place of your 9005 and 9006 bulbs.

9005 and 9006 sockets plug into your harness, 9004 socket plugs into your 9004 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Note: if your low beam stays on with your high beam it will overheat the 9004 bulb and possibly damage the socket and wires.

To build these I will need the following info from your factory harness:

You will need a volt meter you can check these.

Are your cars headlights power or ground trigger.

On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

9005 and 9006 sockets with “A” and “B” marked

 

$50.00 a pair (2 harness)

Please email with the information required and your PayPal address and I will send an invoice.

9006 low and 9005 high beam to 9007

This will allow you to install a 9007 bulb in place of your 9005 and 9006 bulbs.

9005 and 9006 sockets plug into your harness, 9007 socket plugs into your 9007 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Note: if your low beam stays on with your high beam it will over heat the 9007 bulb and possibly damage the socket and wires. I recomend the relayed version.

To build these I will need the following info from your factory harness:

You will need a volt meter you can check these.

Are your cars headlights power or ground trigger.

On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

9005 and 9006 sockets with “A” and “B” marked

 

$50.00 a pair (2 harness)

Please email with the information required and your PayPal address and I will send an invoice.

9006 low and 9005 high beam to H13

9005 9006 to H13This will allow you to install a H13 bulb in place of your 9005 and 9006 bulbs.

9005 and 9006 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires. I recomend the relayed version.

To build these I will need the following info from your factory harness:

You will need a volt meter you can check these.

Are your cars headlights power or ground trigger.

On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

9005 and 9006 sockets with “A” and “B” marked

 

$50.00 pair (2 harness)

Please email with the information required and your PayPal address and I will send an invoice.

9006 low and 9005 high beam to H4

9006 low 9005 high to H4
9006 low 9005 high to H4

This will allow you to install a H4 bulb in place of your 9005 and 9006 bulbs. 9005 and 9006 sockets plug into your harness, H4 socket plugs into your H4 bulb. Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Note: if your low beam stays on with your high beams it will overheat the H4 bulb and possibly damage the socket and wires.I recomend the relayed version.

To build these I will need the following info from your factory harness: You will need a volt meter you can check these. Are your cars headlights power or ground trigger. On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket) On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)

9005 and 9006 sockets with “A” and “B” marked

H4 is the same as 9003, 6014, 6006

$50.00 pair (2 harness)

Please email with the information required and your PayPal address and I will send an invoice.

9006 Lowbeam / 9005 Highbeam To 9004 With Relay

Installing a 9004 headlight in place of your factory 9006 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a 9004 bulb in place of your 9006 and 9005 bulbs.

9006 and 9005 sockets plug into your harness, 9004 socket plugs into your 9004 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$70.00 pair (2 harness)

 

9006 Lowbeam / 9005 Highbeam To 9007 With Relay

Installing a 9007 headlight in place of your factory 9006 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a 9007 bulb in place of your 9006 and 9005 bulbs.

9006 and 9005 sockets plug into your harness, 9007 socket plugs into your 9007 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$70.00 pair (2 harness)

 

9006 Lowbeam / 9005 Highbeam To H13 With Relay

Installing a H13 headlight in place of your factory 9006 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your 9006 and 9005 bulbs.

9006 and 9005 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$70.00 pair (2 harness)

 

9006 Lowbeam / 9005 Highbeam To H4 With Relay

9006 low 9005 high to H4 with relay
9006 low 9005 high to H4 with relay

This will allow you to install a H4 bulb in place of your 9006 and 9005 bulbs.

9006 and 9005 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$70.00 pair (2 harness)

 

9006 to 880

9006 to 880 Headlight Adaptor Harness
9006 to 880

This will allow you to install a 880 bulb in place of your 9006 bulb.

9006 socket plugs into your harness, 880 socket plugs into 880 bulb.

made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9006 to 9005

9006 to 9005
9006 to 9005

This will allow you to install a 9005 bulb in place of your 9006 bulb.

9006 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

9006 to H1

9006 socket plugs into your harness, H1 socket plugs into H1 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This has connector for the bulb and one to ground the bulb.

Euro 2 connector

$25.00 pair (2 harness)

 

Asian 2 pin connector

$25.00 pair (2 harness)

9006 to H4 low beam / 9005 to H1 high beam

9006 to H4 / 9005 to H1
9006 to H4 / 9005 to H1

This is a full set of harness to allow you to install aftermarket headlights.

2) 9006 to H4 harness wired to turn on low beam.

2) 9005 to H1 for lights with asian 2 prong adaptor harness is wired as high beam.

If you want the 9005 to H1 to be a single wire connector Just let me know in checkout and what terminal you need for the H1 ground wire.

JDM headlight harness set.$50.00

9006 to H4 wired as high beam

9006 to H4
9006 to H4

This will allow you to install a H4 bulb in place of your 9006 bulb. This will only operate the high beam part of the H4 bulb.

9006 socket plugs into your harness, H4 socket plugs into H4 bulb.

This can be used on the Toyota Headlight H4/H1 headlights.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

9006 to H4 wired as low beam

9006 to H4 low beam only
9006 to H4 low beam only

This will allow you to install a H4 bulb in place of your 9006 bulb. This will only operate the low beam part of the H4 bulb.

9006 socket plugs into your harness, H4 socket plugs into H4 bulb.

This can be used on the Toyota Headlight H4/H1 headlights.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

9006 to H7

9006 to H7
9006 to H7

9006 socket plugs into your harness, H7 socket plugs into H7 bulb.

made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

9006 to H8 or H11

 

9006 to H8/H11
9006 to H8/H11

9006 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

9006 to H9

9006 to H9 Headlight Adaptor Harness
9006 to H9

This will allow you to install a H9 bulb in place of your 9006 bulb.

9006 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires

$25.00 pair. (2 harnesses)

9006 WIG-WAG PIGTAIL

This is a 9006 to 9006 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

9007

 

 

 

9007 to 9004

9007 to 9004
9007 to 9004

This will allow you to install a 9004 bulb in place of your 9007 bulb.

9007 socket plugs into your harness, 90047 socket plugs into 9004 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

9007 TO 9005 high beam

H4 to H8 low / H8 high beam
9007 to 9005 

If you are swaping out your 9007 to a 9005 high beam this harness will plug right in.

9007 socket plugs into your harness, 9005 socket plugs into 9005 bulbs.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harness)

9007 TO 9006 low and 9005 high beam

9007 to 9006 low and 9005 high beams
9007 to 9006 low and 9005 high beams

If you are swaping out your single bulb headlights to the dual bulbs this will allow you to install a 9005 and 9006  bulbs in place of your 9007 bulb.

9007 socket plugs into your harness, 9005 and 9006 sockets plug into 9005 and 9006 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair. (2 harness)

9007 TO 9006 low beam

9007 to 9006 low beam only
9007 to 9006 low beam only

If you are swaping out your 9007 to a 9006 low beam this harness will plug right in.

9007 socket plugs into your harness, 9006 socket plugs into 9006 bulbs.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harness)

9007 to H13

 

9007 to H13
9007 to H13

This will allow you to install a H13  bulb in place of your 9007 bulb.

9007 socket plugs into your harness, H13 socket plugs into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

9007 to H4

9007 to H4
9007 to H4

This will allow you to install a H4 bulb in place of your 9007 bulb.

9007 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair. (2 harnesses)

9007 TO H7 low and H7 high

9007 to H7 low and H7 high beams
9007 to H7 low and H7 high beams

This will allow you to install a H7 low beam and H7 high beam bulbs in place of your 9007 bulb.

9007 socket plugs into your harness, H7 and H7 sockets plug into H7 and H7 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair (2 harness)

9007 TO H8 low and H8 high

This will allow you to install a H8 low beam and H8 high beam bulbs in place of your 9007 bulb.

9007 socket plugs into your harness, H8 and H8 sockets plug into H8 low beam and H8 high beam bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair (2 harness)

9007 to H8 or H11

9007 to H8 Lowbeam only
9007 to H8 Lowbeam only

This will allow you to install a H8/H11 bulb in place of your 9007 bulb.

9007 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired as low beam.

$25.00 pair. (2 harnesses)

9007 TO H9 low and H9 high beam

9007 to H9low H9high

9007 socket plugs into your harness, H9 and H9 sockets plug into H9 and H9 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair. (2 harness)

9007 WIG-WAG PIGTAIL

9007 to 9007This is a 9007 to 9007 harness so you can add a wig-wag unit without cutting into your factory harness.

Made with 14 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)