Headlight Adaptors H1/H4/H7/H8/H9/H11/H13 to .. Headlight harnesses

1. Connector info

Connectors are classified by the terminal not the plastic housing:

20140325_184339
A 9005 Male connector

A male connector is the same as the bulb.

 

 

 

 

 

 

 

9005 Female connector
9005 Female connector

A female connector is the same as on the harness and plugs into the bulb.

 

 

 

 

 

Example: If you have a 9006 bulb and are installing a H8 bulb you would want: Male 9006 to Female H8.

 

 

Headlight switch position does not make a bulb brighter, The bulb and headlight housing is what changes the bulb light output.

Example: A headlight bulb that is a single filament  (H1, H3, H7, H8, H9) will be the same brightness when the headlight switch is in the low or high position.

Note: If you are installing LED lights please make sure you have the proper operating system, Most LEDS are made to work with a power trigger system.

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

H1

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

 

H1 to 9005

H1 Euro to 9005
H1 euro to 9005

This will allow you to install a 9005 bulb in place of your H1 bulb.

H1 sockets plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$25.00 pair. (2 harnesses)

H1 to 9006

This will allow you to install a 9006 bulb in place of your H1 bulb.

H1 sockets plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H1 to H8 or H11

H1 sockets plugs into your harness, H8/H11 socket plugs into H8 or H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H1 to H9

This will allow you to install a H9 bulb in place of your H1 bulb.

H1 sockets plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H13

The H13 bulb turns off the low beam when the high beam is turn on, and it will continue to work as such.

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

 

H13 to 9004

H13 to 9004
H13 to 9004

H13 socket plugs into your harness, 9004 socket plugs into 9004 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H13 to 9007

H13 to 9007
H13 to 9007

H13 socket plugs into your harness, 9007 socket plugs into 9007 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H13 to H1 High beam

This will allow you to install a H1 bulb in place of your H13 bulb.

H13 socket plugs into your harness, H1 socket plugs into H1 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as high beam.

No low beam output.

H13 to H1 low beam
H13 to H1 high beam only euro

Euro

$25.00 pair. (2 harnesses)

 

Asian 2 pin H1

H13 to H1 Asian 2 pin Low beam only
H13 to H1 Asian 2 pin Low beam only

$25.00 pair. (2 harnesses)

H13 to H1 Low and H1 High

H13 to H1 low and H1 high with Euro connectors
H13 to H1 low and H1 high with Euro connectors
H13 to H1 Low and H1 High beam Asian 2 pin
H13 to H1 Low and H1 High beam Asian 2 pin

This will allow you to install a H1 low beam bulb and H1 high beam bulb in place of your H13 bulb.

H13 socket plugs into your harness, H1 socket plugs into H1 low beam bulb and H1 high beam bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$50.00.00 pair. (2 harnesses) euro H1 connector’s

 

$50.00.00 pair. (2 harnesses) Asian 2 pin connector connector’s

H13 to H1 Low beam

H13 socket plugs into your harness, H1 socket plugs into H1 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as low beam.

No high beam output.

H13 to H1 Asian 2 pin Low beam only
H13 to H1 Asian 2 pin Low beam only.

 

H13 to H1 Asain 2 pin

$25.00 pair. (2 harnesses)

 

 

H13 to H1 low beam
H13 to H1 low beam Euro connectors

H13 to H1 Euro

$25.00 pair. (2 harnesses)

H13 to H4

H13 to H4
H13 to H4

This will allow you to install a H4 bulb in place of your H13 bulb.

H13 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H13 to H7 High beam

This will allow you to install a H7 bulb in place of your H13 bulb.

H13 to H7 High beam only
H13 to H7 High beam only

H13 socket plugs into your harness, H7 socket plugs into H7 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as high beam.

No low beam output.

$25.00 pair. (2 harnesses)

 

 

H13 to H7 Low and H7 High

H13 to H7 low and H7 highbeam
H13 to H7 low and H7 highbeam

This will allow you to install a H7 bulb in place of your H13 bulb.

H13 socket plugs into your harness, H7 socket plugs into H7 low beam bulb and H7 High beam bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00.00 pair. (2 harnesses)

H13 to H7 Low beam

H13 to H7 Low beam only
H13 to H7 Low beam only

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as low beam.

No high beam output.

 

$25.00 pair. (2 harnesses)

 

 

H13 to H8/H11 High beam

H13 to H8 low beam only
H13 to H8 high beam only

This will allow you to install a H8/H11 bulb in place of your H13 bulb.

H13 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as high beam.

No low beam output.

 

$25.00 pair. (2 harnesses)

H13 to H8/H11 low and 9005 high beam

H13 to H8 low and 9005 high beam
H13 to H8 low and 9005 high beam

This will allow you to install a H8/H11 low and 9005 high bulb in place of your H13 bulb.

H13 socket plugs into your harness, H8/H11 and 9005 sockets plug into H8 and 9005 bulb.

Made with 16gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

50.00 pair (2 harness)

 

 

H13 to H8/H11 Low and H8/H11 high beam

 

H13 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$50.00 pair. (2 harnesses)

H13 to H8/H11 Low beam

H13 to H8 low beam only
H13 to H8 low beam only

H13 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as low beam.

No high beam output.

 

$25.00 pair. (2 harnesses)

H13 to H9 High beam

H13 to H9 High
H13 to H9 High

This will allow you to install a H9 bulb in place of your H13 bulb.

H13 socket plugs into your harness, H9 socket plugs into H9 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as high beam.

No low beam output.

$25.00 pair. (2 harnesses)

H13 to H9 Low and H9 high beam

H13 to H9 low and H9 high

H13 socket plugs into your harness, H9 socket plugs into H9 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 pair. (2 harnesses)

H13 to H9 Low beam

H13 to H9 low beam only
H13 to H9 low beam only

H13 socket plugs into your harness, H9 socket plugs into H9 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as low beam.

No high beam output.

$25.00 pair. (2 harnesses)

H13 WIG-WAG PIGTAIL

H13 to H13This is a H13 to H13 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

H4

The H4 bulb turns off the low beam when the high beam is turn on, and it will continue to work as such.

H4 is wired the same as 6006, 6014.

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

H4 to 9004

H4 to 9004
H4 to 9004

This will allow you to install a 9004  bulb in place of your H4 bulb.

H4 socket plugs into your harness, 9004 sockets plug into 9004 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair. (2 harnesses)

H4 to 9005 TO OPERATE AS HIGH BEAM

H4 to 9005
H4 to 9005

This will allow you to install a 9005 bulb in place of your H4 bulb and have it turn on as a high beam.

H4 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair. (2 harnesses)

H4 to 9005 to operate as low beam

This will allow you to install a 9005 bulb in place of your H4 bulb and have it turn on as a low beam.

H4 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

 

$25.00 pair. (2 harnesses)

H4 to 9006 low and 9005 high beam

H4 to 9006 low and 9005 high
H4 to 9006 low and 9005 high

This will allow you to install a 9005 and 9006  bulbs in place of your H4 bulb.

H4 socket plugs into your harness, 9005 and 9006 sockets plug into 9005 and 9006 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

$50.00 pair (2 harness)

H4 to 9006 low and 9006 high beam

H4 to 9006 low and 9006high beamThis will allow you to install a 9006 and 9006  bulbs in place of your H4 bulb.

H4 socket plugs into your harness, 9006 and 9006 sockets plug into 9006 and 9006 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

$50.00 pair (2 harness)

H4 to 9006 TO OPERATE AS A LOW BEAM

This will allow you to install a 9006 bulb in place of your H4 bulb and have it turn on as a low beam.H4 to 9006

H4 socket plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair. (2 harnesses)

H4 to 9007


H4 to 9007
H4 to 9007

This will allow you to install a 9007  bulb in place of your H4 bulb.

H4 socket plugs into your harness, 9007 sockets plug into 9007 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair. (2 harnesses)

H4 to H1 High beam

This will allow you to install a H1 bulb in place of your H4 bulb.

H4 socket plugs into your harness, H1 socket plugs into H1 bulb or HID.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as high beam.

No low beam output.

H4 to H1 Euro High beam only
H4 to H1 Euro High beam only

Euro

$25.00 pair. (2 harnesses)

 

Asian 2 pin H1

$25.00 pair. (2 harnesses)

H4 to H1 Low and 9005 High

This will allow you to install a H1 low beam bulb and 9005 high beam bulb in place of your H4 bulb.

H4 socket plugs into your harness, H1 socket plugs into H1 low beam bulb and 9005 high beam bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$50.00.00 pair. (2 harnesses) euro H1 connector’s

 

$50.00.00 pair. (2 harnesses) Asian 2 pin connector connector’s

H4 to H1 Low and H1 High

H4 to H1 low and H1 high euro style
H4 to H1 low and H1 high euro style

This will allow you to install a H1 low beam bulb and H1 high beam bulb in place of your H4 bulb.

H4 socket plugs into your harness, H1 socket plugs into H1 low beam bulb and H1 high beam bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$50.00.00 pair. (2 harnesses) euro H1 connector’s

 

$50.00.00 pair. (2 harnesses) Asian 2 pin connector connector’s

H4 to H1 Low beam

H4 ro H1 Euro low beam only
H4 to H1 Euro low beam only

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired to trigger as low beam.

No high beam output.

Euro

$25.00 pair. (2 harnesses)

H4 to H1 Asian 2 pin
H4 to H1 Asian 2 pin

Asian 2 pin H1

$25.00 pair. (2 harnesses)

H4 to H13

This will allow you to install a H13  bulb in place of your H4 bulb.

H4 to H13
H4 to H13

H4 socket plugs into your harness, H13 sockets plug into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair. (2 harnesses)

H4 to H7

H4 to H7 Low beam
H4 to H7 Low beam

This will allow you to install a H7 bulb in place of your H4 bulb.

H4 socket plugs into your harness, H7 socket plugs into H7 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

H4 to H7 low beam turns the light on when your switch is in the low beam posistion.

H4 to H7 high beam turns the light on when your switch is in the high beam posistion.

H4 o H7 High beam
H4 to H7 High beam

 

$12.50 each (1 harness)


 

 

$25.00 pair


H4 to H7 low and H1 high beam

This will allow you to install a H7 lowbeam and H1 highbeam bulbs in place of your H4 bulb.

H4 socket plugs into your harness, H7 socket plugs into H7 bulb and H1 sockets plug into H1 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

 

Euro style H1 connectors.

$25.00 each (1 harness)

H4 to H7 low and H1 high Asian 2 pin
H4 to H7 low and H1 high Asian 2 pin

Asian 2 pin H1 connectors.

$25.00 each (1 harness)

H4 to H7 low and H7 high beam

H4 to H7 low and H7 high beam
H4 to H7 low and H7 high beam

This will allow you to install a H7 lowbeam and H7 highbeam bulbs in place of your H4 bulb.

H4 socket plugs into your harness, H7 and H7 sockets plug into H7 and H7 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

H4 to H7 low and H9 high beam

H4 to H7 low and H9 high beam
H4 to H7 low and H9 high beam

This will allow you to install a H7 lowbeam and H9 highbeam bulbs in place of your H4 bulb.

H4 socket plugs into your harness, H7 and H9 sockets plug into H7 and H9 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

H4 to H8 low and 9005 high beam

H4 to H8 and 9005This will allow you to install a H8 low and 9005 high bulb in place of your H4 bulb.

H4 socket plugs into your harness, H8 and 9005 sockets plug into H8 and 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$50.00 pair (2 harness)

 

 

H4 to H8 or H11 low and H8 or H11 high beam

H4 to H8/H11 low and H8/H11 high beams
H4 to H8/H11 low and H8/H11 high beams

This will allow you to install a H8 or H11 lowbeam and H8 or H11 highbeam bulbs in place of your H4 bulb.

H4 socket plugs into your harness, H8/H11 and H8/H11sockets plug into H8 or H11and H8 or H11bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

H4 to H8 or H11 low and H9 high beam

H4 to H8 low and H9 high beam
H4 to H8 low and H9 high beam

This will allow you to install a H8 or H11 lowbeam and H9 highbeam bulbs in place of your H4 bulb.

H4 socket plugs into your harness, H8/H11 and H9 sockets plug into H8/H11 and H9 bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

 

H4 to H8 or H11 TO OPERATE AS A LOW BEAM

H4 to H8/H11 low beam only
H4 to H8/H11 low beam only

H4 socket plugs into your harness, H8 socket plugs into H8 or H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H4 to H8/H11 LOW and H8/H11 HIGH BEAM

H4 to H9 low and H9 high beamH4 socket plugs into your harness, H8 and H8 sockets plug into H8 low and H8 high beam bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

 

$25.00 each (1 harness)

 

$50.00 each (2 harness)

H4 to H9 LOW and H9 HIGH BEAM

H4 to H9 low and H9 high beamH4 socket plugs into your harness, H9 and H9 sockets plug into H9 low and H9 high beam bulbs.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

 

$25.00 each (1 harness)

 

$50.00 each (2 harness)

H4 to H9 TO OPERATE AS A HIGH BEAM

H4 to H8/H11 low beam only
H4 to H9 high beam only

H4 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This will turn the H9 on only when you have switched to high beams.

H4 is the same as 9003, 6014, 6006.

 

$25.00 pair. (2 harnesses)

H4 to H9 TO OPERATE AS A LOW BEAM

H4 to H9 Low beam only
H4 to H9 Low beam only

H4 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This will turn the H9 on only when you have your low beams on.

H4 is the same as 9003, 6014, 6006.

 

$25.00 pair. (2 harnesses)

H4 WIG-WAG PIGTAIL

This is a H4 to H4 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 14 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

H7

 

Note; Some H7 headlights use adapters to the harness. The H7 sockets used in these harness either plug right onto the bulb (female style) or the pins match the bulb (male style).

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

H7 Low beam and H7 High beam to H4

Installing a H4 headlight in place of your factory H7 low beam and H7 high beam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7 and H7 bulbs.

H7 and H7 sockets plug into your harness, H4 socket plugs into H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires. I recommend the relayed version.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 each (1 harness)

H7 Low beam and H9 High beam to H4

H7 low H8 high to H4
H7 low H9 high to H4

Installing a H4 headlight in place of your factory H7 and H9 setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7 and H9 bulbs.

H7 and H9 sockets plug into your harness, H4 socket plugs into H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires. I recomend the relayed version.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 each (1 harness)

H7 Lowbeam / H7 Highbeam To H4 With Relay

H7low H7high to H4 relayedInstalling a H4 headlight in place of your factory H7 lowbeam and H7 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7and H7 bulbs.

H7 and H7 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$35.00 each (1 harness)

H7 Lowbeam / H9 Highbeam To H4 With Relay

H7low H7high to H4 relayedInstalling a H4 headlight in place of your factory H7 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7 low beam bulb and H9 high beam bulbs.

H7 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$35.00 each (1 harness)

H7 to 9005

H7 to 9005
H7 to 9005

This will allow you to install a 9005 bulb in place of your H7 bulb.

H7 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H7 to 9006

This will allow you to install a 9006 bulb in place of your H7 bulb.

H7 socket plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H7 to H4 wired as high beam

H7 to H4 High beam only
H7 to H4 High beam only

This will allow you to install a H4 bulb in place of your H7 bulb. This will only operate the high beam part of the H4 bulb.

H7 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

H7 to H4 wired as low beam

This will allow you to install a H4 bulb in place of your H7 bulb. This will only operate the low beam part of the H4 bulb.

H7 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

H7 to H8 or H11

H7 to H8
H7 to H8

H7 socket plugs into your harness, H8/H11 socket plugs into H8 or H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H7 to H9

This will allow you to install a H9 bulb in place of your H7 bulb.

H7 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H7 WIG-WAG PIGTAIL

This is a H7 to H7 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16

H7 to H7
H7 to H7

gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

H8 H11

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

 

H8 H11 to H1

H8 TO H1 EUROH8 or H11 socket plugs into your harness, H1 socket plugs into H1 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This has connector for the bulb and one to ground the bulb.

$25.00 pair (2 harness)

H8 H11 to H1 2 pin

H8 H11 to H1 Asian 2 pin
H8 H11 to H1 Asian 2 pin

H8 H11 socket plugs into your harness, H1 socket plugs into H1 bulb with 2 pin adaptor.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This has connector for the bulb and one to ground the bulb.

Terminals are 11/16″ or 17mm apart.

$25.00 pair (2 harness)

H8 or H11 to 880

9005 to 880 Headlight Adaptor Harness
H8/H11 to 880

This will allow you to install a 880 bulb in place of your H8 or H11 bulb.

H8/H11 socket plugs into your harness, 880 socket plugs into 880 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 pair. (2 harnesses)

 

H8 or H11 to 9005

H8/H11 to 9005
H8/H11 to 9005

H8/H11 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 pair. (2 harnesses)

 

H8 or H11 to 9006

H8 to 9006
H8 to 9006

This will allow you to install a 9006 bulb in place of your H8 or H11 bulb.

H8/H11 socket plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 pair. (2 harnesses)

 

 

 

H8 or H11 to H13

H8 to H13 low beam only
H8 to H13 low beam only

H8/H11 socket plugs into your harness, H13 socket plugs into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 pair. Operates low beam fillament of H13 only. (2 harnesses)

$25.00 pair. Operates High beam fillament of H13 only. (2 harnesses)

 

H8 or H11 to H7

H8/H11 to H7
H8/H11 to H7

H8/H11 socket plugs into your harness, H7 socket plugs into H7 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 pair. (2 harnesses)

 

H8 or H11 to H9

H8 to H9
H8 to H9

H8/H11 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 pair. (2 harnesses)

 

H8/H11 Low beam and 9005 High beam to H13

H8 low 9005 High to H13
H8 low 9005 High to H13

This will allow you to install a H13 bulb in place of your H8/H11and 9005 bulbs.

H8/H11 and 9005 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 each (1 harness)

H8/H11 Low beam and H8/H11 High beam to H13

H8 low H8 high to H13
H8 low H8 high to H13

This will allow you to install a H13 bulb in place of your H8/H11and H8/H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 each (1 harness)

H8/H11 Low beam and H8/H11 High beam to H4

H8 low and H8 high beams to H4
H8 low and H8 high beams to H4

Installing a H4 headlight in place of your factory H8/H11 and H8/ H11 setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11and H8/H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H4 socket plugs into H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires. I recomend the relayed version.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 each (1 harness)

H8/H11 Low beam and H9 High beam to H13

H8/H11 low. H9 high to H13
H8/H11 low. H9 high to H13

H8/H11 and H9 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 each (1 harness)

H8/H11 Low beam and H9 High beam to H4

H8 low and H9 high beams to H4
H8 low and H9 high beams to H4

This will allow you to install a H4 bulb in place of your H8 and H9 bulbs.

H8/H11 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and socket and possibly damage the wires. I recommend the relayed harness.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

$25.00 each (1 harness)

H8/H11 Lowbeam / 9005 Highbeam To H13With Relay

H8 low 9005 high to H13 relayed
H8 low 9005 high to H13 relayed

Installing a H13 headlight in place of your factory H8/H11 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your H8/H11and 9005 bulbs.

H8/H11 and 9005 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

 

 

H8/H11 Lowbeam / 9005 Highbeam To H4 With Relay

Installing a H4 headlight in place of your factory H8/H11 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11and 9005 bulbs.

H8low 9005high to H4 relayed pair
H8low 9005high to H4 with relay

H8/H11 and 9005 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

 

 

H8/H11 Lowbeam / H8/H11 Highbeam To H13 With Relay

Installing a H13 headlight in place of your factory H8/H11 lowbeam and H8/H11 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your H8/H11and H8/H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

 

 

H8/H11 Lowbeam / H8/H11 Highbeam To H4 With Relay

H8 low H9 high to H4 with relay
H8/H11 low H8/H11 high to H4 with relay

Installing a H4 headlight in place of your factory H8/H11 lowbeam and H8/H11 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11 and H8H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

 

H8/H11 Lowbeam / H9 Highbeam To H13 With Relay

Installing a H13 headlight in place of your factory H8/H11 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your H8/H11and H9 bulbs.

H8/H11 and H9 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

H8/H11 Lowbeam / H9 Highbeam To H4 With Relay

H8 low H9 high to H4 with relay
H8 low H9 high to H4 with relay

Installing a H4 headlight in place of your factory H8/H11 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11 and H9 bulbs.

H8/H11 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

 

H8/H11 WIG-WAG PIGTAIL

This is a H8/H11 to H8/H11 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)

H9

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

 

H9 Low beam and H9 High beam to H4

H9 low and H9 high beams to H4
H9 low and H9 high beams to H4

This will allow you to install a H4 bulb in place of your H9 low beam and H9 high beam bulbs.

H9 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb. Please order the relayed harness.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 each (1 harness)

H9 Lowbeam / H9 Highbeam To H4 With Relay

H9 low H9 high to H4 with relay
H9 low H9 high to H4 with relay

Installing a H4 headlight in place of your factory H9 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H9 and H9 bulbs.

H9 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

 

$35.00 each (1 harness) motorcycles

 

$70.00 pair (2 harness) cars

 

H9 to 880

This will allow you to install a 880 bulb in place of your H9 bulb.

H9 socket plugs into your harness, 880 socket plugs into 880 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H9 to 9005

H9 to 9005
H9 to 9005

H9 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H9 to 9006

This will allow you to install a 9006 bulb in place of your H9 bulb.

H9 socket plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H9 to H13

H9 to H13 low beam only
H9 to H13 low beam only

This will allow you to install a H13  bulb in place of your H9 bulb.

H9 socket plugs into your harness, H13 socket plugs into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Wired as low beam.

$25.00 pair. (2 harnesses)

H9 to H7

H9 to H7
H9 to H7

This will allow you to install a H7 bulb in place of your H9 bulb.

H9 socket plugs into your harness, H7 socket plugs into H7 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H9 to H8 or H11

This will allow you to install a H8 or H11  bulb in place of your H9 bulb.

H9 socket plugs into your harness, H8 /H11 socket plugs into H8 or H11 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

H9 WIG-WAG PIGTAIL

This is a H9 to H9 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

$25.00 pair (2 harness)