H8 H11

H8 / H11 INFO

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

H8 / H11 to H1 Euro Style

H8 to H1 Euro Low beam

H8 to H1 Euro Low beam

H8 or H11 socket plugs into your harness, H1 socket plugs into H1 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

This has connector for the bulb and one to ground the bulb.

H8 / H11 to H1 Euro style low beam only: $25.00 pair (2 harness)

 

H8 to H1 2 Pin Style

H8 H11 to H1 Asian 2 pin

H8 H11 to H1  2 pin

H8 H11 socket plugs into your harness, H1 socket plugs into H1 bulb with 2 pin adaptor.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

Terminals are 11/16″ or 17mm apart.

H8 / H11 to H1 @2 Pin style: $25.00 pair (2 harness)

 

H8 to H7

H8/H11 to H7

H8/H11 to H7

H8/H11 socket plugs into your harness, H7 socket plugs into H7 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8 / H11 to H7: $25.00 pair. (2 harnesses)

 

H8 / H11 to H9

H8 to H9

H8 to H9

H8/H11 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8 / H11 to H9: $25.00 pair. (2 harnesses)

 

H8 / H11 to H13 Low Beam Only

H8 to H13 low beam only

H8 to H13 low beam only

H8/H11 socket plugs into your harness, H13 socket plugs into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

Operates low beam fillament of H13 only

H8 to H13 Low beam only: 25.00 pair. . (2 harnesses)

 

H8 / H11 to H13 High Beam Only

H8/H11 socket plugs into your harness, H13 socket plugs into H13 bulb.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

Operates High beam fillament of H13 only.

H8 to H13 High beam only: $25.00 pair. Operates High beam fillament of H13 only. (2 harnesses)

 

H8 / H11 to 880

9005 to 880 Headlight Adaptor Harness

H8/H11 to 880

This will allow you to install a 880 bulb in place of your H8 or H11 bulb.

H8/H11 socket plugs into your harness, 880 socket plugs into 880 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8 to 880: $25.00 pair. (2 harnesses)

 

H8 / H11 to 9005

H8/H11 to 9005

H8/H11 to 9005

H8/H11 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 to 9005: $25.00 pair. (2 harnesses)

 

H8 / H11 to 9006

H8 to 9006

H8 to 9006

This will allow you to install a 9006 bulb in place of your H8 or H11 bulb.

H8/H11 socket plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8 /H11 to 9006: $25.00 pair. (2 harnesses)

 

H8 / H11 Low and H8 / H11 High Beam to H4

H8 low and H8 high beams to H4

H8 low and H8 high beams to H4

Installing a H4 headlight in place of your factory H8/H11 and H8/ H11 setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11and H8/H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H4 socket plugs into H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires. I recomend the relayed version.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8/H11 low and H8/H11 to H4: $25.00 each (1 harness)

 

H8 /H11 Low and H8 / H11 High Beam to H4 with Relay

H8 low H9 high to H4 with relay

H8/H11 low H8/H11 high to H4 with relay

Installing a H4 headlight in place of your factory H8/H11 lowbeam and H8/H11 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11 and H8H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8/H11 low and H8/H11 high beam to H4 with relay: $35.00 each (1 harness) motorcycles

H8/H11 low and H8/H11 high beam to H4 with relay: $70.00 pair (2 harness) cars

 

H8 / H11 Low and H8 / H11 High Beam to H13

H8 low H8 high to H13

H8 low H8 high to H13

This will allow you to install a H13 bulb in place of your H8/H11and H8/H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 low and H8/H11 High beam to H13: $25.00 each (1 harness)

 

H8 / H11 Low and H8 /H11 High Beam to H13 with Relay

Installing a H13 headlight in place of your factory H8/H11 lowbeam and H8/H11 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your H8/H11and H8/H11 bulbs.

H8/H11 and H8/H11 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 low and H8/H11 High beam to to H13 with relay: $35.00 each (1 harness) motorcycles

H8/H11 low and H8/H11 High beam to to H13 with relay: $70.00 pair (2 harness) cars

 

H8 / H11 Low and H9 High Beam to H4 

H8 low and H9 high beams to H4

H8 low and H9 high beams to H4

This will allow you to install a H4 bulb in place of your H8 and H9 bulbs.

H8/H11 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and socket and possibly damage the wires. I recommend the relayed harness.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 low and H9 high beam to H4: $25.00 each (1 harness)

 

H8 / H11 low and H9 High Beam to H4 with Relay

H8 low H9 high to H4 with relay

H8 low H9 high to H4 with relay

Installing a H4 headlight in place of your factory H8/H11 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11 and H9 bulbs.

H8/H11 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8/H11 low and H9 High beam to H4 wity relay: $35.00 each (1 harness) motorcycles

H8/H11 low and H9 High beam to H4 wity relay: $70.00 pair (2 harness) cars

 

H8 / H11 Low and H9 High Beam to H13

H8/H11 low. H9 high to H13

H8/H11 low. H9 high to H13

H8/H11 and H9 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 Low and H9 High beam to H13: $25.00 each (1 harness)

 

H8 /H11 Low and H9 High Beam to H13 with Relay

Installing a H13 headlight in place of your factory H8/H11 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your H8/H11and H9 bulbs.

H8/H11 and H9 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8 Low and H9 High beam to H13 with relay: $35.00 each (1 harness) motorcycles

H8 Low and H9 High beam to H13 with relay: $70.00 pair (2 harness) cars

 

H8 / H11 Low and 9005 High Beam to H4 

This will allow you to install a H4 bulb in place of your H8/H11 and 9005 bulbs.

H8/H11 and 9005 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 Low and 9005 High beam to H4: $25.00 each (1 harness)

 

H8 / H11 Low and 9005 High Beam to H4 with Relay

H8 low 9005 high to H4 with relay

H8 low 9005 high to H4 with relay

Installing a H4 headlight in place of your factory H8/H11 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H8/H11and 9005 bulbs.

H8/H11 and 9005 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 Low and 9005 High beam to H4 with relay: $35.00 each (1 harness) motorcycles

H8/H11 Low and 9005 High beam to H4 with relay: $70.00 pair (2 harness) cars

 

H8 /H11 Low and 9005 High Beam to H13

H8 low 9005 High to H13

H8 low 9005 High to H13

This will allow you to install a H13 bulb in place of your H8/H11and 9005 bulbs.

H8/H11 and 9005 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam it will over heat the H13 bulb and possibly damage the socket and wires.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 Low and 9005 High beam to H13: $25.00 each (1 harness)

 

H8 / H11 Low and 9005 High Beam to H13 with Relay

H8 low 9005 high to H13 relayed

H8 low 9005 high to H13 relayed

Installing a H13 headlight in place of your factory H8/H11 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H13 bulb in place of your H8/H11and 9005 bulbs.

H8/H11 and 9005 sockets plug into your harness, H13 socket plugs into your H13 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H8 is the same as H11 / 880/ 886 / 893 / 899 / 894 / 896

H8/H11 Low and 9005 High beam to H13 with relay: $35.00 each (1 harness) motorcycles

H8/H11 Low and 9005 High beam to H13 with relay: $70.00 pair (2 harness) cars

 

H8 / H11 to H8 / H11 Wig Wag

This is a H8/H11 to H8/H11 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.

Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.

H8/H11 to H8/H11 Wig wag: $25.00 pair (2 harness)

 

EMAIL