H7

H7 INFO

Note; Some H7 headlights use adapters to the harness. The H7 sockets used in these harness either plug right onto the bulb (female style) or the pins match the bulb (male style).

By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.

ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.

 

H7 lowbeam and H7 highbeam to H4

H7 low H7 high to H4

H7 lowbeam H7 highbeam to H4

Installing a H4 headlight in place of your factory H7 low beam and H7 high beam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7 and H7 bulbs.

H7 and H7 sockets plug into your harness, H4 socket plugs into H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires. I recommend the relayed version.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 each (1 harness)

 

H7 lowbeam and H7 highbeam to H4 with relay

H7 low H7 high to H4 with relay

H7 low H7 high to H4 with relay

This will allow you to install a H4 bulb in place of your H7and H7 bulbs.

H7 and H7 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$35.00 each (1 harness)

 

 

H7 lowbeam and H7 highbeam to two H4 sockets with relay

This will allow you to install two H4 LED bulbs in place of your H7 and H7 bulbs.

This will turn on both H4 lowbeams when switch is in the lowbeam position and both highbeam when switch is in the highbeam postion.

H7 and H7 sockets plug into your harness, H4 sockets plug into your two H4 LED bulbs.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

This harness is only to be used with LED H4 lights.

Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$50.00 each (1 harness)

 

H7 to H4 lowbeam

H7 to H4 Low beam only

H7 to H4 Low beam only

This will allow you to install a H4 bulb in place of your H7 bulb. This will only operate the low beam part of the H4 bulb.

H7 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

 

H7 to H4 highbeam

H7 to H4 High beam only

H7 to H4 High beam only

This will allow you to install a H4 bulb in place of your H7 bulb. This will only operate the high beam part of the H4 bulb.

H7 socket plugs into your harness, H4 socket plugs into H4 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

H4 is the same as 9003, 6014, 6006

$25.00 pair (2 harness)

 

H7 lowbeam and H9 highbeam to H4

H7 low H8 high to H4

H7 lowbeam H9 highbeam to H4

Installing a H4 headlight in place of your factory H7 and H9 setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7 and H9 bulbs.

H7 and H9 sockets plug into your harness, H4 socket plugs into H4 bulb.

Note: if your low beam stays on with your high beam it will over heat the H4 bulb and possibly damage the socket and wires. I recomend the relayed version.

You will need to be able to test your factory harness for power and ground trigger and power and ground location in the sockets.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 each (1 harness)

 

H7 lowbeam and H9 highbeam to H4 with relay

 

Installing a H4 headlight in place of your factory H7 lowbeam and H9 highbeam setup, then this harness will plug in to make the install easier.

This will allow you to install a H4 bulb in place of your H7 low beam bulb and H9 high beam bulbs.

H7 and H9 sockets plug into your harness, H4 socket plugs into your H4 bulb.

Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.

This only works if your low beam stays on with you high beam.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$35.00 each (1 harness)

 

H7 to H8

H7 to H8

H7 to H8

H7 socket plugs into your harness, H8/H11 socket plugs into H8 or H11 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

 

H7 to H9

 

This will allow you to install a H9 bulb in place of your H7 bulb.

H7 socket plugs into your harness, H9 socket plugs into H9 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

 

H7 to 9005

H7 to 9005

H7 to 9005

This will allow you to install a 9005 bulb in place of your H7 bulb.

H7 socket plugs into your harness, 9005 socket plugs into 9005 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

 

H7 to 9006

This will allow you to install a 9006 bulb in place of your H7 bulb.

H7 socket plugs into your harness, 9006 socket plugs into 9006 bulb.

Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.

$25.00 pair. (2 harnesses)

 

EMAIL