9006 INFO
By purchasing any headlight harness adapter you assume all responsibility for knowing the proper ways of testing your factory harness and any circumstances that can happen by changing bulbs.
ALL HARNESS ARE ARE FOR OFFROAD USE ONLY.
9006 to 880
This will allow you to install a 880 bulb in place of your 9006 bulb.
9006 socket plugs into your harness, 880 socket plugs into 880 bulb.
made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$35.00 pair (2 harness)
9006 to 9005
This will allow you to install a 9005 bulb in place of your 9006 bulb.
9006 socket plugs into your harness, 9005 socket plugs into 9005 bulb.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$35.00 pair. (2 harnesses)
9006 lowbeam and 9005 highbeam to 9004
This will allow you to install a 9004 bulb in place of your 9005 and 9006 bulbs.
9005 and 9006 sockets plug into your harness, 9004 socket plugs into your 9004 bulb.
Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
Note: if your low beam stays on with your high beam it will overheat the 9004 bulb and possibly damage the socket and wires.
To build these I will need the following info from your factory harness:
You will need a volt meter you can check these.
Are your cars headlights power or ground trigger.
On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)
On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)
$60.00 a pair (2 harness)
Please email with the information required and your PayPal address and I will send an invoice.
9006 lowbeam and 9005 highbeam to 9004 with relay
Installing a 9004 headlight in place of your factory 9006 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.
This will allow you to install a 9004 bulb in place of your 9006 and 9005 bulbs.
9006 and 9005 sockets plug into your harness, 9004 socket plugs into your 9004 bulb.
Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.
This only works if your low beam stays on with you high beam.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$85.00 pair (2 harness)
9006 lowbeam and 9005 highbeam to 9007
This will allow you to install a 9007 bulb in place of your 9005 and 9006 bulbs.
9005 and 9006 sockets plug into your harness, 9007 socket plugs into your 9007 bulb.
Made with 16 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
Note: if your low beam stays on with your high beam it will over heat the 9007 bulb and possibly damage the socket and wires. I recomend the relayed version.
To build these I will need the following info from your factory harness:
You will need a volt meter you can check these.
Are your cars headlights power or ground trigger.
On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)
On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)
$60.00 a pair (2 harness)
Please email with the information required and your PayPal address and I will send an invoice.
9006 lowbeam and 9005 highbeam to 9007 with relay
Installing a 9007 headlight in place of your factory 9006 lowbeam and 9005 highbeam setup, then this harness will plug in to make the install easier.
This will allow you to install a 9007 bulb in place of your 9006 and 9005 bulbs.
9006 and 9005 sockets plug into your harness, 9007 socket plugs into your 9007 bulb.
Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam.
This only works if your low beam stays on with you high beam.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$85.00 pair (2 harness)
9006 to H1 Euro style
9006 socket plugs into your harness, H1 socket plugs into H1 bulb.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
This has connector for the bulb and one to ground the bulb.
Euro Single connector
$35.00 pair (2 harness)
9006 to H1 2 pin style
9006 socket plugs into your harness, H1 socket plugs into H1 2 pin bulb adapter.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
This has connector plugs into a 2 pin bulb adapter.
Asian 2 pin connector
$35.00 pair (2 harness)
9006 to H4 lowbeam

9006 to H4 low beam only
This will allow you to install a H4 bulb in place of your 9006 bulb.
9006 socket plugs into your harness, H4 socket plugs into H4 bulb.
This can be used on the Toyota Headlight H4/H1 headlights.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
This will only operate the low beam part of the H4 bulb.
H4 is the same as 9003, 6014, 6006
$35.00 pair (2 harness)
9006 to H4 highbeam
This will allow you to install a H4 bulb in place of your 9006 bulb.
9006 socket plugs into your harness, H4 socket plugs into H4 bulb.
This can be used on the Toyota Headlight H4/H1 headlights.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
This will only operate the high beam part of the H4 bulb.
H4 is the same as 9003, 6014, 6006
$35.00 pair (2 harness)
9006 lowbeam and 9005 highbeam to H4
This will allow you to install a H4 bulb in place of your 9005 and 9006 bulbs. 9005 and 9006 sockets plug into your harness, H4 socket plugs into your H4 bulb. Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
Note: if your low beam stays on with your high beams it will overheat the H4 bulb and possibly damage the socket and wires.I recomend the relayed version.
To build these I will need the following info from your factory harness: You will need a volt meter you can check these. Are your cars headlights power or ground trigger. On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket) On the high beam socket 9005 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)
H4 is the same as 9003, 6014, 6006
$60.00 pair (2 harness)
Please email with the information required and your PayPal address and I will send an invoice.
9006 lowbeam and 9005 highbeam to H4 with relay
This will allow you to install a H4 bulb in place of your 9006 and 9005 bulbs.
9006 and 9005 sockets plug into your harness, H4 socket plugs into your H4 bulb.
Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam. This only works if your low beam stays on with you high beam.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$85.00 pair (2 harness)
9006 lowbeam and H8 highbeam to H4
This will allow you to install a H4 bulb in place of your H8 and 9006 bulbs. H8 and 9006 sockets plug into your harness, H4 socket plugs into your H4 bulb. Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
Note: if your low beam stays on with your high beams it will overheat the H4 bulb and possibly damage the socket and wires.I recomend the relayed version.
To build these I will need the following info from your factory harness: You will need a volt meter you can check these. Are your cars headlights power or ground trigger. On the low beam socket 9006 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket) On the high beam socket H8 what wire is the power. (the socket is marked with “A” or “B” were the wire go into the socket)
H4 is the same as 9003, 6014, 6006
$60.00 pair (2 harness)
Please email with the information required and your PayPal address and I will send an invoice.
9006 lowbeam H8 highbeam to H4 with relay
This will allow you to install a H4 bulb in place of your 9006 and H8 bulbs.
9006 and H8 sockets plug into your harness, H4 socket plugs into your H4 bulb.
Note: if your low beam stays on with your high beam then this relayed harness will shut off the lowbeam filament when you switch to highbeam. This only works if your low beam stays on with you high beam.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
NOTE: If you are installing this on Led headlights make sure you car is a power triggered system.
$85.00 pair (2 harness)
9006 to H7
9006 socket plugs into your harness, H7 socket plugs into H7 bulb.
made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$35.00 pair. (2 harnesses)
9006 to H8/H11
9006 socket plugs into your harness, H8/H11 socket plugs into H8/H11 bulb.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires.
$35.00 pair. (2 harnesses)
9006 to H9
This will allow you to install a H9 bulb in place of your 9006 bulb.
9006 socket plugs into your harness, H9 socket plugs into H9 bulb.
Made with 14 gauge SXL wire, terminals are crimped and soldered and loom is installed to protect the wires
$35.00 pair. (2 harnesses)
9006 to 9006 wigwag
This is a 9006 to 9006 harness so you can add a wig-wag unit without cutting into your factory harness.This will allow you to cut the wires on this harness as needed to hook up your wig-wag unit.
Made with 16 gauge SXL wire, terminals a crimped and soldered and loom is installed to protect the wires.
$35.00 pair (2 harness)